CHAPTER-40

Rubber And Articles Thereof

Notes:

1. Except where the context otherwise requires, throughout this Schedule the expression “rubber” means the following products, whether or not vulcanised or hard:

natural rubber, balata, gutta-percha, guayule, chicle and similar natural gums, synthetic, rubber factice derived from oils, and such substances reclaimed

2. This Chapter does not cover :

(a) Goods of Section XI (textiles and textile articles);

(b) Footwear or parts thereof of Chapter 64;

(c) Headgear or parts thereof (including bathing caps) of Chapter 65;

(d) Mechanical or electrical appliances or parts thereof of Section XVI (including electrical goods of all kinds), of hard rubber;

(e) Articles of Chapter 90,92,94 or 96; or

(f) Articles of Chapter 95 (Other than sports gloves, mittens and mitts and articles of headings 4011 to 4013.

3. In headings 4001 to 4003 and 4005, the expression “Primary forms” applies only to the following forms:

(a) Liquids and pastes (including latex, whether or not pre-vulcanised, and other dispersions and solutions);

(b) Blocks of irregular shape, lumps, bales, and powders, granules, crumbs and similar bulk forms.

4. In Note 1 to this Chapter and in heading 4002, the expression “synthetic rubber” applies to:

(a) Unsaturated synthetic substances which can be irreversibly transformed by vulcanisation with sulphur into non - thermoplastic substances which, at a temperature between 180C and 290C , will not break on being extended to three times their original length and will return, after being extended to twice their original length, within a period of five minutes, to a length not greater than one and a half times their original length. For the purposes of this test, substances necessary for the cross-linking, such as Vulcanising activators or accelerators, may be added; the presence of substances as provided for by Note 5(B)(ii) and (iii) is also permitted. However, the presence of any substances not necessary for the cross-linking, such as extenders, Plasticisers and fillers, is not permitted;

(b) Thioplasts (TM ); and

(c) Natural rubber modified by grafting or mixing with plastics, depolymerised natural rubber, mixtures of unsaturated synthetic substances with saturated synthetic high polymers provided that all the above-mentioned products comply with the requirements concerning vulcanisation, elongation and recovery in (a) above.

5. (A) Headings 4001 and 4002 do not apply to any rubber or mixture of rubbers which has been compounded, before or after coagulation, with :

(i) Vulcanising agents, accelerators, retarders or activators (other than those added for the preparation of pre-vulcanised rubber latex);

(ii) Pigments of other colouring matter, other than those added solely for the purpose of identification;

(iii) Plasticisers or extenders (except mineral oil in the case of oil-extended rubber), fillers, reinforcing agents, organic solvents or any other substances, except those permitted under (B);

(B) the presence of the following substances in any rubber or mixture of rubbers shall not affect its classification in heading 4001 or 4002, as the case may be, provided that such rubber or mixture of rubbers retains its essential character as a raw material:

(i) emulsifiers or anti-tack agents;

(ii) Small amounts of breakdown products of emulsifiers;

(iii) Very small amounts of the following: heat-sensitive agents (generally for obtaining thermosensitive rubber latexes), cationic surface-active agents (generally for obtaining electro-positive rubber latexes), anti-oxidants, coagulants, crumbling agents, freeze-resisting agents, peptisers, preservatives, stabilisers, viscosity-control agents, or similar special-purpose additives.

6. For the purposes of heading 4004, the expression “waste, parings and scrap” means rubber waste, parings and scrap from the manufacture or working of rubber and rubber goods definitely not usable as such because of cutting-up, wear or other reasons.

7. Thread wholly of vulcanised rubber, of which may cross-sectional dimension exceeds mm., is to be classified as strip, rods or profile shapes, of heading 4008

8. Heading 4010 includes conveyor or transmission belts or belting of textile fabric impregnated, coated, covered or laminated with rubber or made from textile yarn or cord impregnated, coated, covered or sheathed with rubber.

9. In headings 4001, 4002, 4003, 4005 and 4008, the expressions “plates”, “sheets”, and “strip” apply only to plates, sheets and strip and to blocks of regular geometric shape, uncut or simply cut to rectangular (including square) shape, whether or not having the character of articles and whether or not printed or otherwise surface-worked, but not otherwise cut to shape or further worked.

In heading 4008 the expression “rods” and “profile shapes” apply only to such products, whether or not cut to length or surface-worked but not otherwise worked.

Supplementary notes:

1. For the purposes of headings 4009 and 4010, while calculating the percentage of rubber compound contents, the weight of canvas, yarn, metallic wires, washers, rivets and the like, which products, shall form integral part of ingredient of such rubber products, shall be taken into an account, but the weight of metallic fitments and surface finishing necessary to make the belting and tubing suitable for particular end uses, shall be ignored

2. Tariff item 4008 21 10 shall also apply to “plates”, “sheets”, and “strips”, whether or not cut to shape and surface-worked or further –worked so as to render them fit for resoling or repairing or re-treading of rubber tyres.

(In Note 4 & 5 letters “Note 5(b)" & “(a)” and “(b)” has been replaced vide NOTIFICATION NO. 94/2008, DT. 02/03/2009)